Dell PowerEdge R360

This article describes the Dell PowerEdge R360 appliance, supported for operational technology (OT) sensors in an enterprise deployment. The Dell PowerEdge R360 is also available for the on-premises management console.

Appliance characteristic Description
Hardware profile E1800
Performance Max bandwidth: 1 Gbps
Max devices: 10,000
Physical Specifications Mounting: 1U with rail kit
Ports: 6x RJ45 1 GbE
Status Supported, available as a preconfigured appliance

The following image shows a view of the Dell PowerEdge R360 front panel:

Photograph of the Dell PowerEdge R360 front panel.

The following image shows a view of the Dell PowerEdge R360 back panel:

Photograph of the Dell PowerEdge R360 back panel.

Specifications

Component Technical specifications
Chassis 1U rack server
Dimensions Height: 1.68 in / 42.8 mm
Width: 18.97 in / 482.0 cm
Depth: 23.04 in / 585.3 mm (without bezel) 23.57 in / 598.9 mm (with bezel)
Processor Intel Xeon E-2434 3.4 GHz
8M Cache
4C/8T, Turbo, HT (55 W) DDR5-4800
Memory 32 GB
Storage 2.4 TB Hard Drive
Network controller - PowerEdge R360 Motherboard with with Broadcom 5720 Dual Port 1Gb On-Board LOM,
- PCIe Blank Filler, Low Profile.
- Intel Ethernet i350 Quad Port 1GbE BASE-T Adapter, PCIe Low Profile, V2
Management iDRAC Group Manager, Disabled
Rack support ReadyRails Sliding Rails With Cable Management Arm

Dell PowerEdge R360 - Bill of materials

Quantity PN Description
1 210-BJTR Base PowerEdge R360 Server
1 461-AAIG Trusted Platform Module 2.0 V3
1 321-BKHP 2.5" Chassis with up to 8 Hot Plug Hard Drives, Front PERC
1 338-CMRB Intel Xeon E-2434 3.4G, 4C/8T, 8M Cache, Turbo, HT (55 W) DDR5-4800
1 412-BBHK Heatsink
1 370-AAIP Performance Optimized
1 370-BBKS 4800 MT/s UDIMMs
2 370-BBKF 16 GB UDIMM, 4800 MT/s ECC
1 780-BCDQ RAID 10
1 405-ABCQ PERC H355 Controller Card
1 750-ACFR Front PERC Mechanical Parts, front load
4 400-BEFU 1.2 TB Hard Drive SAS 12 Gbps 10k 512n 2.5in Hot Plug
1 384-BBBH Power Saving BIOS Settings
1 387-BBEY No Energy Star
1 384-BDML Standard Fan
1 528-CTIC iDRAC9, Enterprise 16G
2 450-AADY C13 to C14, PDU Style, 10 AMP, 6.5 Feet (2m), Power Cord
1 330-BCMK Riser Config 2, Butterfly Gen4 Riser (x8/x8)
1 329-BJTH PowerEdge R360 Motherboard with with Broadcom 5720 Dual Port 1Gb On-Board LOM
1 414-BBJB PCIe Blank Filler, Low Profile
1 540-BDII Intel Ethernet i350 Quad Port 1GbE BASE-T Adapter, PCIe Low Profile, V2, FIRMWARE RESTRICTIONS APPLY
1 379-BCRG iDRAC, Factory Generated Password, No OMQR
1 379-BCQX iDRAC Service Module (ISM), NOT Installed
1 325-BEVH PowerEdge 1U Standard Bezel
1 350-BCTP Dell Luggage Tag R360
1 379-BCQY iDRAC Group Manager, Disabled
1 470-AFBU BOSS Blank
1 770-BCWN ReadyRails Sliding Rails With Cable Management Arm
2 450-AKMP Dual, Hot-Plug, Redundant Power Supply (1+1), 600W MM for US
Dual, Hot-Plug, Redundant Power Supply (1+1), 700W MM HLAC (Only for 200-240Vac) titanium for Europe

Install Defender for IoT software on the DELL R360

This procedure describes how to install Defender for IoT software on the Dell R360.

The installation process takes about 20 minutes. During the installation, the system restarts several times.

To install Defender for IoT software:

  1. Connect the screen and keyboard to the appliance, and then connect to the CLI.

  2. Connect an external CD or disk-on-key that contains the software you downloaded from the Azure portal.

  3. Start the appliance.

  4. Continue with the generic procedure for installing Defender for IoT software. For more information, see Defender for IoT software installation.

Next steps

Continue learning about the system requirements for physical or virtual appliances. For more information, see Which appliances do I need?.

Then, use any of the following procedures to continue: