Usage Guidance

Microsoft.AspNetCore.SystemWebAdapters provides an emulation layer to mimic behavior from ASP.NET framework on ASP.NET Core. Below are some guidelines for some of the considerations when using them:

HttpContext lifetime

The adapters are backed by HttpContext which cannot be used past the lifetime of a request. Thus, HttpContext when run on ASP.NET Core cannot be used past a request as well, while on ASP.NET Framework it would work at times. An ObjectDisposedException will be thrown in cases where it is used past a request end.

Recommendation: Store the values needed into a POCO and hold onto that.

Conversion to HttpContext

There are two ways to convert an HttpContext to a HttpContext:

  • Implicit casting
  • Constructor usage

Recommendation: For the most cases, implicit casting should be preferred as this will cache the created instance and ensure only a single HttpContext per request.

CurrentCulture is not set by default

In ASP.NET Framework, CurrentCulture was set for a request, but this is not done automatically in ASP.NET Core. Instead, you must add the appropriate middleware to your pipeline.

Recommendation: See ASP.NET Core Localization for details on how to enable this.

Simplest way to enable this with similar behavior as ASP.NET Framework would be to add the following to your pipeline:

app.UseRequestLocalization();

CurrentPrincipal

In ASP.NET Framework, CurrentPrincipal and Current would be set to the current user. This is not available on ASP.NET Core out of the box. Support for this is available with these adapters by adding the ISetThreadCurrentPrincipal to the endpoint (available to controllers via the SetThreadCurrentPrincipalAttribute). However, it should only be used if the code cannot be refactored to remove usage.

Recommendation: If possible, use the property User or User instead by passing it through to the call site. If not possible, enable setting the current user and also consider setting the request to be a logical single thread (see below for details).

Request thread does not exist in ASP.NET Core

In ASP.NET Framework, a request had thread-affinity and Current would only be available if on that thread. ASP.NET Core does not have this guarantee so Current will be available within the same async context, but no guarantees about threads are made.

Recommendation: If reading/writing to the HttpContext, you must ensure you are doing so in a single-threaded way. You can force a request to never run concurrently on any async context by setting the ISingleThreadedRequestMetadata. This will have performance implications and should only be used if you can't refactor usage to ensure non-concurrent access. There is an implementation available to add to controllers with SingleThreadedRequestAttribute:

[SingleThreadedRequest]
public class SomeController : Controller
{
    ...
} 

Request may need to be prebuffered

By default, the incoming request is not always seekable nor fully available. In order to get behavior seen in .NET Framework, you can opt into prebuffering the input stream. This will fully read the incoming stream and buffer it to memory or disk (depending on settings).

Recommendation: This can be enabled by applying endpoint metadata that implements the IPreBufferRequestStreamMetadata interface. This is available as an attribute PreBufferRequestStreamAttribute that can be applied to controllers or methods.

To enable this on all MVC endpoints, there is an extension method that can be used as follows:

app.MapDefaultControllerRoute()
    .PreBufferRequestStream();

Response may require buffering

Some APIs on Response require that the output stream is buffered, such as Output, End(), Clear(), and SuppressContent.

Recommendation: In order to support behavior for Response that requires buffering the response before sending, endpoints must opt-into it with endpoint metadata implementing IBufferResponseStreamMetadata.

To enable this on all MVC endpoints, there is an extension method that can be used as follows:

app.MapDefaultControllerRoute()
    .BufferResponseStream();

Shared session state

In order to support Session, endpoints must opt-into it via metadata implementing ISessionMetadata.

Recommendation: To enable this on all MVC endpoints, there is an extension method that can be used as follows:

app.MapDefaultControllerRoute()
    .RequireSystemWebAdapterSession();

This also requires some implementation of a session store. For details of options here, see here.

Remote session exposes additional endpoint for application

The remote session support exposes an endpoint that allows the core app to retrieve session information. This may cause a potentially long-lived request to exist between the core app and the framework app, but will time out with the current request or the session timeout (by default is 20 minutes).

Recommendation: Ensure the API key used is a strong one and that the connection with the framework app is done over SSL.

Virtual directories must be identical for framework and core applications

The virtual directory setup is used for route generation, authorization, and other services within the system. At this point, no reliable method has been found to enable different virtual directories due to how ASP.NET Framework works.

Recommendation: Ensure your two applications are on different sites (hosts and/or ports) with the same application/virtual directory layout.