PoRegisterDeviceForIdleDetection function (ntifs.h)

The PoRegisterDeviceForIdleDetection routine enables or cancels idle detection and sets idle time-out values for a device.

Syntax

PULONG PoRegisterDeviceForIdleDetection(
  [in] PDEVICE_OBJECT     DeviceObject,
  [in] ULONG              ConservationIdleTime,
  [in] ULONG              PerformanceIdleTime,
  [in] DEVICE_POWER_STATE State
);

Parameters

[in] DeviceObject

A pointer to the driver-created DEVICE_OBJECT for the device. This parameter can point to a physical device object (PDO) or a functional device object (FDO).

[in] ConservationIdleTime

Sets the time-out value (in seconds) to apply when the system power policy optimizes for energy conservation. Specify zero to disable idle detection when conservation policy is in effect.

[in] PerformanceIdleTime

Sets the time-out value (in seconds) to apply when the system power policy optimizes for performance. Specify zero to disable idle detection when performance policy is in effect.

[in] State

Specifies the device power state to be requested in an IRP_MN_SET_POWER request when either ConservationIdleTime or PerformanceIdleTime has been met. Possible values are the DEVICE_POWER_STATE values.

Return value

PoRegisterDeviceForIdleDetection returns a pointer to the idle counter to indicate that idle detection has been enabled. It returns NULL to indicate that idle detection has been disabled, that an idle counter could not be allocated, or that one or both of the time-out values were invalid.

Remarks

PoRegisterDeviceForIdleDetection enables drivers to use the idle detection mechanism provided by the power manager. Drivers call PoRegisterDeviceForIdleDetection for any of the following reasons:

• To enable idle detection for the device and set initial idle time-out values.
• To change the idle time-out values for a device.
• To disable idle detection for a device.

After enabling a device for idle detection, a driver calls PoSetDeviceBusy whenever the device is in use, passing the non-NULL idle pointer returned by PoRegisterDeviceForIdleDetection. Calling PoSetDeviceBusy restarts the idle countdown. Note that a driver must not pass a NULL pointer to PoSetDeviceBusy.

Whenever the device satisfies the current idle time-out value, the power manager sends an IRP_MN_SET_POWER request to the top of the device stack, specifying device power state State. In response to the IRP, each driver performs any device-specific tasks required before the power state transition, then passes the IRP to the next-lower driver. When the IRP reaches the bus driver, that driver puts the device in the requested lower power state and completes the IRP.

PoRegisterDeviceForIdleDetection sets time-out values for both conservation and performance. The ConservationIdleTime value applies when the system power policy optimizes for conservation; the PerformanceIdleTime value applies when the system power policy optimizes for performance. Typically, the applicable policy depends upon the power source: when running with AC power, the system optimizes for performance, and when running off a battery, the system optimizes for conservation.

Certain devices can specify time-out values of -1 to use the standard power policy time-outs for their device class. The standard time-out values provide for better system integration for supported standard device classes. At present, WDM supports this feature for devices of type FILE_DEVICE_DISK and FILE_DEVICE_MASS_STORAGE. PoRegisterDeviceForIdleDetection returns NULL if -1 is specified for a device of an unsupported type. For information about device types, see Specifying Device Types.

Only one idle detection can be set per device. Subsequent calls to PoRegisterDeviceForIdleDetection change the idle detection values.

If both ConservationIdleTime and PerformanceIdleTime are zero, this routine cancels all idle detection for the device and returns NULL.

PoRegisterDeviceForIdleDetection can free a driver from the need to perform its own idle detection. However, drivers can also implement their own idle detection.

Requirements

See also

IRP

IRP_MN_SET_POWER

PoSetDeviceBusy