MmAllocatePagesForMdl function (wdm.h)

The MmAllocatePagesForMdl routine allocates zero-filled, non-paged, physical memory pages to an MDL.

Syntax

PMDL MmAllocatePagesForMdl(
  [in] PHYSICAL_ADDRESS LowAddress,
  [in] PHYSICAL_ADDRESS HighAddress,
  [in] PHYSICAL_ADDRESS SkipBytes,
  [in] SIZE_T           TotalBytes
);

Parameters

[in] LowAddress

Specifies the physical address of the start of the first address range from which the allocated pages can come. If MmAllocatePagesForMdl cannot allocate the requested number of bytes in the first address range, it iterates through additional address ranges to get more pages. At each iteration, MmAllocatePagesForMdl adds the value of SkipBytes to the previous start address to obtain the start of the next address range.

[in] HighAddress

Specifies the physical address of the end of the first address range from which the allocated pages can come.

[in] SkipBytes

Specifies the number of bytes to skip from the start of the previous address range from which the allocated pages can come. SkipBytes must be an integer multiple of the virtual memory page size, in bytes.

[in] TotalBytes

Specifies the total number of bytes to allocate for the MDL.

Return value

MmAllocatePagesForMdl returns one of the following:

Remarks

Drivers that are running in Windows Server 2003 Service Pack 1 (SP1) and later versions of Windows should use the MmAllocatePagesForMdlEx routine instead of MmAllocatePagesForMdl. MmAllocatePagesForMdlEx provides better performance than MmAllocatePagesForMdl by avoiding unnecessary flushes of the translation lookaside buffer (TLB) and cache memory.

The physical memory pages that are returned by MmAllocatePagesForMdl are typically not contiguous pages. MmAllocatePagesForMdl always fills the allocated pages in the returned MDL with zeros.

MmAllocatePagesForMdl is designed to be used by kernel-mode drivers that do not need corresponding virtual addresses (that is, they need physical pages and do not need the pages to be physically contiguous) or by kernel-mode drivers that can achieve substantial performance gains if physical memory for a device is allocated in a specific physical address range. A driver for an AGP graphics card is an example of such a driver.

Depending on how much physical memory is currently available in the requested ranges, MmAllocatePagesForMdl might return an MDL that describes less memory than was requested. The routine returns NULL if no memory was allocated. The caller should check the amount of memory that is actually allocated to the MDL.

The caller must use MmFreePagesFromMdl to release the memory pages that are described by an MDL that was created by MmAllocatePagesForMdl. After calling MmFreePagesFromMdl, the caller must also call ExFreePool to release the memory that is allocated for the MDL structure itself.

In Windows 2000 and later versions of Windows, the maximum amount of memory that MmAllocatePagesForMdl can allocate in a single call is (4 gigabytes - PAGE_SIZE). The routine can satisfy an allocation request for this amount only if enough pages are available.

MmAllocatePagesForMdl runs at IRQL <= APC_LEVEL. Windows Server 2008 and later versions of the Windows operating system enable MmAllocatePagesForMdl callers to call at DISPATCH_LEVEL. However, you can improve driver performance by calling at APC_LEVEL or below.

Calling MmAllocatePagesForMdl from a special kernel asynchronous procedure call (APC) can lead to a recursive acquisition of an exclusive lock, which is only in a critical region (user or normal kernel APCs disabled) but not in a guarded region (all APCs disabled).

Requirements

See also

ExFreePool

MmAllocatePagesForMdlEx

MmFreePagesFromMdl

MmMapLockedPages