WCN_VALUE_TYPE_CONFIGURATION_ERROR enumeration (wcntypes.h)
The WCN_VALUE_TYPE_CONFIGURATION_ERROR enumeration defines possible error values returned to a device while attempting to configure to, and associate with, the WLAN.
Syntax
typedef enum tagWCN_VALUE_TYPE_CONFIGURATION_ERROR {
WCN_VALUE_CE_NO_ERROR = 0,
WCN_VALUE_CE_OOB_INTERFACE_READ_ERROR = 1,
WCN_VALUE_CE_DECRYPTION_CRC_FAILURE = 2,
WCN_VALUE_CE_2_4_CHANNEL_NOT_SUPPORTED = 3,
WCN_VALUE_CE_5_0_CHANNEL_NOT_SUPPORTED = 4,
WCN_VALUE_CE_SIGNAL_TOO_WEAK = 5,
WCN_VALUE_CE_NETWORK_AUTHENTICATION_FAILURE = 6,
WCN_VALUE_CE_NETWORK_ASSOCIATION_FAILURE = 7,
WCN_VALUE_CE_NO_DHCP_RESPONSE = 8,
WCN_VALUE_CE_FAILED_DHCP_CONFIG = 9,
WCN_VALUE_CE_IP_ADDRESS_CONFLICT = 10,
WCN_VALUE_CE_COULD_NOT_CONNECT_TO_REGISTRAR = 11,
WCN_VALUE_CE_MULTIPLE_PBC_SESSIONS_DETECTED = 12,
WCN_VALUE_CE_ROGUE_ACTIVITY_SUSPECTED = 13,
WCN_VALUE_CE_DEVICE_BUSY = 14,
WCN_VALUE_CE_SETUP_LOCKED = 15,
WCN_VALUE_CE_MESSAGE_TIMEOUT = 16,
WCN_VALUE_CE_REGISTRATION_SESSION_TIMEOUT = 17,
WCN_VALUE_CE_DEVICE_PASSWORD_AUTH_FAILURE = 18
} WCN_VALUE_TYPE_CONFIGURATION_ERROR;
Constants
WCN_VALUE_CE_NO_ERROR Value: 0 No error. An application must be prepared to handle devices that signal 'No Error' even if the device detected an error. |
WCN_VALUE_CE_OOB_INTERFACE_READ_ERROR Value: 1 Could not read the out-of-band (OOB) interface. |
WCN_VALUE_CE_DECRYPTION_CRC_FAILURE Value: 2 Could not decrypt the Cyclic Redundancy Check (CRC) value. |
WCN_VALUE_CE_2_4_CHANNEL_NOT_SUPPORTED Value: 3 The 2.4 GHz channel is not supported. |
WCN_VALUE_CE_5_0_CHANNEL_NOT_SUPPORTED Value: 4 The 5.0 GHz channel is not supported. |
WCN_VALUE_CE_SIGNAL_TOO_WEAK Value: 5 The wireless signal is not strong enough to initiate a connection. Note Not supported in WPS 2.0. |
WCN_VALUE_CE_NETWORK_AUTHENTICATION_FAILURE Value: 6 Network authentication failed. Note Not supported in WPS 2.0. |
WCN_VALUE_CE_NETWORK_ASSOCIATION_FAILURE Value: 7 Network association failed. Note Not supported in WPS 2.0. |
WCN_VALUE_CE_NO_DHCP_RESPONSE Value: 8 The DHCP server did not respond. Note Not supported in WPS 2.0. |
WCN_VALUE_CE_FAILED_DHCP_CONFIG Value: 9 DHCP configuration failed. Note Not supported in WPS 2.0. |
WCN_VALUE_CE_IP_ADDRESS_CONFLICT Value: 10 There was an IP address conflict. Note Not supported in WPS 2.0. |
WCN_VALUE_CE_COULD_NOT_CONNECT_TO_REGISTRAR Value: 11 Could not connect to the registrar. |
WCN_VALUE_CE_MULTIPLE_PBC_SESSIONS_DETECTED Value: 12 Multiple push button configuration (PBC) sessions were detected. |
WCN_VALUE_CE_ROGUE_ACTIVITY_SUSPECTED Value: 13 Rogue activity is suspected. |
WCN_VALUE_CE_DEVICE_BUSY Value: 14 The device is busy. |
WCN_VALUE_CE_SETUP_LOCKED Value: 15 Setup is locked. |
WCN_VALUE_CE_MESSAGE_TIMEOUT Value: 16 The message timed out. Note Not supported in WPS 2.0. |
WCN_VALUE_CE_REGISTRATION_SESSION_TIMEOUT Value: 17 The registration session timed out. Note Not supported in WPS 2.0. |
WCN_VALUE_CE_DEVICE_PASSWORD_AUTH_FAILURE Value: 18 Device password authentication failed. |
Requirements
Requirement | Value |
---|---|
Minimum supported client | Windows Vista [desktop apps only] |
Minimum supported server | Windows Server 2008 [desktop apps only] |
Header | wcntypes.h |